Sub-Sets:Individual rods assembled into groups of two,three ,or four.
And the products surface was Sand Blasting Surface Treatment.Core Splice:Galvanized steel,sub-setted and gritted.Need Sand Blasting Surface Treatment.Filler Rods:Aluminum alloy,sub-setted,or single rods,not gritted.
Filler Rods are not required for selected sizes corresponding to tabular information on catalog pages.
Outer Splice:Aluminum alloy,sub-setted and gritted.Need Sand Blasting Surface Treatment.
Center Mark and Color Code:Establishes recommended alignment of rods during application and Assist in identification of conductor size
Length:corresponding to tabular information appearing on catalog pages.
Identification Tape:Shows catalog number,nominal sizes.

catalogue number	Conductor ACSR/LGJ	Standards	Length of splice mm
			Core splice	filler rods	outer splice
JL-50/8	LGJ-50/8	GB1179-74LGJ	508		1372
JL-70/10	LGJ-70/10	GB1179-83	406	406	1499
JL-95/15	LGJ-95/15	GB1179-83	508	508	1905
JL-95/20	LGJ-95/20	GB1179-83	510	510	1727
JL-95/55	LGJ-95/55	GB1179-74LGJ	790		2500
JL-120/20	LGJ-120/20	GB1179-83	508	508	20557
JL-120/0	LGJ-120/0	GB1179-74LGJ	610	610	2210
JL-150/8	LGJ-150/8	GB1179-74LGJ	635	635	2387
JL-150/20	LGJ-150/20	GB1179-83	508	508	2261
JL-150/25	LGJ-150/25	GB1179-83	635	635	2413
JL-185/25	LGJ-185/25	GB1179-83	635	635	2642
JL-185/30	LGJ-185	GB1179-83	660	660	2667
JL-185/0	LGJ-210/25	GB1179-74LGJ	686	686	2692
JL-210/25	LGJ-240	GB1179-83	630	630	2743
JL-240/0	LGJ-240/30	GB1179-74LGJ	787	787	3226
JL-240/30	LGJ-240/40	GB1179-83	686	686	3073
JL-240/40	LGJ-240/40	GB1179-83	737	737	3073
JL-240/0	LGJ-240/0	GB1179-74	658	628	3124
JL-300	LGJ-300/15	GB1179-74	711	711	3406
JL-300/25	LGJ-300/25	GB1179-83	635	635	3759
JL-300/40	LGJ-300/40	GB1179-83	737	737	3429
JL-300/0	LGJ-300	GB1179-74	1041	1041	3657
JL-300/50	LGJ-300/50	GB1179-83	-	-	-
JL-300/70	LGJ-300/70	GB1179-83	-	-	-
JL-400/25	LGJ-400/25	GB1179-83	635	635	4013
JL-400/35	LGJ-400/35	GB1179-83	686	686	4242
JL-400/50	LGJ-400/50	GB1179-83	787	787	4243
JL-500/45	LGJ-500/45		-	-	-
JL-500/35	LGJ-500/35		-	-	-
JL-500/65	LGJ-500/65		-	-	-

Heliformed Damper
Damping devices are designed for the single purpose of reducing vibration.This single function is entirely different from that of protecting against (1)stress concentrat ions,(2)fretting or abrasion,and(3)arc-over burning.Because of this,damping devices should be considered only as supplemental to Armor Rod or other hardware at tangent supports.Dampers are also used as supplemental protection at dead-ents.The degree of protection needed on a specific line depends upon a number of factors such as line design, temperature,tension,exposure to wind flow,and vibration history on similar construction in the same area.MATERIAL:The solid polyvinyl chloride helical rod material.

catalogue number	Suitable Conductor		Suitable Conductor
	Diameter Range O.D mm		ACSR LGJ/LGJF	AAC LJ	AS GJ
VD-1	6.35	8.28	25/4.35/6	25.35	25.35
VD-2	8.29	11.71	50/8 50/30 70/10	50 70	50 70
VD-3	11.7	14.3	70/40 95/15 95/20	95 120	95 100 120
			95/55 120/7 150/8
			120/25 120/70 150/8
VD-4	14.31	19.3	150/20 150/25 150/35	150 185 210
			185/10 185/25 185/30
			210/10